当前文档版本为 NDK-v0.7.0,您可以访问当前页面的 开发中 版本以获取最近可能的更新。

SPI Receive Send Polling

1 功能概述

本例程演示如何使用 SPI HAL Driver 实现查询方式的 SPI收发功能。

2 环境准备

  • 硬件设备与线材:

    • PAN107X EVB 核心板底板各两块

    • JLink 仿真器(用于烧录例程程序)

    • USB-TypeC 线两条(用于底板供电和查看串口打印 Log)

    • 杜邦线数根或跳线帽数个(用于连接各个硬件设备)

  • 硬件接线:

    • 将 EVB 核心板插到底板上

    • 使用 USB-TypeC 线,将 PC USB 插口与 EVB 底板 USB->UART 插口相连

    • 使用杜邦线将 EVB0 底板上的 P11(MOSI)、P03(CS)、P04(CLK)、P05(MISO)分别接入EVB1对应相同PAD上

    • 使用杜邦线将 JLink 仿真器的:

      • SWD_CLK 引脚与 EVB 底板的 P00 排针相连

      • SWD_DAT 引脚与 EVB 底板的 P01 排针相连

      • SWD_GND 引脚与 EVB 底板的 GND 排针相连

  • PC 软件:

    • 串口调试助手(UartAssist)或终端工具(SecureCRT),波特率 921600(用于接收串口打印 Log)

3 编译和烧录

例程位置:<PAN10XX-NDK>\01_SDK\nimble\samples\peripheral\spi_master_poll_send_receive\keil_107x

NDK>\01_SDK\nimble\samples\peripheral\spi_slave_poll_receive_send\keil_107x

双击NDK>\01_SDK\nimble\samples\peripheral\spi_master_poll_send_receive\keil_107x目录下Keil Project 文件打开工程进行编译并烧录至EVB0板。

双击NDK>\01_SDK\nimble\samples\peripheral\spi_slave_poll_receive_send\keil_107x目录下Keil Project 文件打开工程进行编译并烧录至EVB1板。

4 例程演示说明

  1. 先烧录spi_slave_poll_receive_send hex至EVB1,芯片会通过串口打印初始化 Log,spi slave进入接收模式,等待接收160个16bit数据:

    Try to load HW calibration data.. DONE.
    - Chip Info         : 0x1
    - Chip CP Version   : 255
    - Chip FT Version   : 4
    - Chip MAC Address  : D0000000037D
    - Chip UID          : 7D0300DDF8375603E8
    - Chip Flash UID    : 425031563233391700DDF8375603E878
    - Chip Flash Size   : 512 KB
    
    APP version: 255.255.65535
    slave start receive 
    
  2. 烧录spi_master_poll_send_receive hex至EVB0,芯片会通过串口打印初始化 Log,spi master进入发送模式,发送16bit数据0x0000~0x009f,Log打印发送的数据,发送完成后Log打印master send done!并进入spi master接收模式:

    Try to load HW calibration data.. DONE.
    - Chip Info         : 0x1
    - Chip CP Version   : 255
    - Chip FT Version   : 4
    - Chip MAC Address  : D000000000D1
    - Chip UID          : D10000F5F737560347
    - Chip Flash UID    : 425031563233391700F5F73756034778
    - Chip Flash Size   : 512 KB
    
    APP version: 255.255.65535
    master send data: 
    0x0000,0x0001,0x0002,0x0003,0x0004,0x0005,0x0006,0x0007,0x0008,0x0009,0x000a,0x000b,0x000c,0x000d,0x000e,0x000f,
    0x0010,0x0011,0x0012,0x0013,0x0014,0x0015,0x0016,0x0017,0x0018,0x0019,0x001a,0x001b,0x001c,0x001d,0x001e,0x001f,
    0x0020,0x0021,0x0022,0x0023,0x0024,0x0025,0x0026,0x0027,0x0028,0x0029,0x002a,0x002b,0x002c,0x002d,0x002e,0x002f,
    0x0030,0x0031,0x0032,0x0033,0x0034,0x0035,0x0036,0x0037,0x0038,0x0039,0x003a,0x003b,0x003c,0x003d,0x003e,0x003f,
    0x0040,0x0041,0x0042,0x0043,0x0044,0x0045,0x0046,0x0047,0x0048,0x0049,0x004a,0x004b,0x004c,0x004d,0x004e,0x004f,
    0x0050,0x0051,0x0052,0x0053,0x0054,0x0055,0x0056,0x0057,0x0058,0x0059,0x005a,0x005b,0x005c,0x005d,0x005e,0x005f,
    0x0060,0x0061,0x0062,0x0063,0x0064,0x0065,0x0066,0x0067,0x0068,0x0069,0x006a,0x006b,0x006c,0x006d,0x006e,0x006f,
    0x0070,0x0071,0x0072,0x0073,0x0074,0x0075,0x0076,0x0077,0x0078,0x0079,0x007a,0x007b,0x007c,0x007d,0x007e,0x007f,
    0x0080,0x0081,0x0082,0x0083,0x0084,0x0085,0x0086,0x0087,0x0088,0x0089,0x008a,0x008b,0x008c,0x008d,0x008e,0x008f,
    0x0090,0x0091,0x0092,0x0093,0x0094,0x0095,0x0096,0x0097,0x0098,0x0099,0x009a,0x009b,0x009c,0x009d,0x009e,0x009f,
    master send done! 
    master turn to receive mode 
    
  3. spi slave接收160个16bit数据并打印接收的数据,同时spi slave进入发送模式,spi slave发送16bit数据0x0000~0x9f9f并打印发送的数据:

    slave receive data: 
    0x0000,0x0001,0x0002,0x0003,0x0004,0x0005,0x0006,0x0007,0x0008,0x0009,0x000a,0x000b,0x000c,0x000d,0x000e,0x000f,
    0x0010,0x0011,0x0012,0x0013,0x0014,0x0015,0x0016,0x0017,0x0018,0x0019,0x001a,0x001b,0x001c,0x001d,0x001e,0x001f,
    0x0020,0x0021,0x0022,0x0023,0x0024,0x0025,0x0026,0x0027,0x0028,0x0029,0x002a,0x002b,0x002c,0x002d,0x002e,0x002f,
    0x0030,0x0031,0x0032,0x0033,0x0034,0x0035,0x0036,0x0037,0x0038,0x0039,0x003a,0x003b,0x003c,0x003d,0x003e,0x003f,
    0x0040,0x0041,0x0042,0x0043,0x0044,0x0045,0x0046,0x0047,0x0048,0x0049,0x004a,0x004b,0x004c,0x004d,0x004e,0x004f,
    0x0050,0x0051,0x0052,0x0053,0x0054,0x0055,0x0056,0x0057,0x0058,0x0059,0x005a,0x005b,0x005c,0x005d,0x005e,0x005f,
    0x0060,0x0061,0x0062,0x0063,0x0064,0x0065,0x0066,0x0067,0x0068,0x0069,0x006a,0x006b,0x006c,0x006d,0x006e,0x006f,
    0x0070,0x0071,0x0072,0x0073,0x0074,0x0075,0x0076,0x0077,0x0078,0x0079,0x007a,0x007b,0x007c,0x007d,0x007e,0x007f,
    0x0080,0x0081,0x0082,0x0083,0x0084,0x0085,0x0086,0x0087,0x0088,0x0089,0x008a,0x008b,0x008c,0x008d,0x008e,0x008f,
    0x0090,0x0091,0x0092,0x0093,0x0094,0x0095,0x0096,0x0097,0x0098,0x0099,0x009a,0x009b,0x009c,0x009d,0x009e,0x009f,
    
    slave send data: 
    0x0000,0x0101,0x0202,0x0303,0x0404,0x0505,0x0606,0x0707,0x0808,0x0909,0x0a0a,0x0b0b,0x0c0c,0x0d0d,0x0e0e,0x0f0f,
    0x1010,0x1111,0x1212,0x1313,0x1414,0x1515,0x1616,0x1717,0x1818,0x1919,0x1a1a,0x1b1b,0x1c1c,0x1d1d,0x1e1e,0x1f1f,
    0x2020,0x2121,0x2222,0x2323,0x2424,0x2525,0x2626,0x2727,0x2828,0x2929,0x2a2a,0x2b2b,0x2c2c,0x2d2d,0x2e2e,0x2f2f,
    0x3030,0x3131,0x3232,0x3333,0x3434,0x3535,0x3636,0x3737,0x3838,0x3939,0x3a3a,0x3b3b,0x3c3c,0x3d3d,0x3e3e,0x3f3f,
    0x4040,0x4141,0x4242,0x4343,0x4444,0x4545,0x4646,0x4747,0x4848,0x4949,0x4a4a,0x4b4b,0x4c4c,0x4d4d,0x4e4e,0x4f4f,
    0x5050,0x5151,0x5252,0x5353,0x5454,0x5555,0x5656,0x5757,0x5858,0x5959,0x5a5a,0x5b5b,0x5c5c,0x5d5d,0x5e5e,0x5f5f,
    0x6060,0x6161,0x6262,0x6363,0x6464,0x6565,0x6666,0x6767,0x6868,0x6969,0x6a6a,0x6b6b,0x6c6c,0x6d6d,0x6e6e,0x6f6f,
    0x7070,0x7171,0x7272,0x7373,0x7474,0x7575,0x7676,0x7777,0x7878,0x7979,0x7a7a,0x7b7b,0x7c7c,0x7d7d,0x7e7e,0x7f7f,
    0x8080,0x8181,0x8282,0x8383,0x8484,0x8585,0x8686,0x8787,0x8888,0x8989,0x8a8a,0x8b8b,0x8c8c,0x8d8d,0x8e8e,0x8f8f,
    0x9090,0x9191,0x9292,0x9393,0x9494,0x9595,0x9696,0x9797,0x9898,0x9999,0x9a9a,0x9b9b,0x9c9c,0x9d9d,0x9e9e,0x9f9f,
    
  4. spi master接收160个16bit数据并打印接收的数据:

    master turn to receive mode 
    receive data: 
    0x0000,0x0101,0x0202,0x0303,0x0404,0x0505,0x0606,0x0707,0x0808,0x0909,0x0a0a,0x0b0b,0x0c0c,0x0d0d,0x0e0e,0x0f0f,
    0x1010,0x1111,0x1212,0x1313,0x1414,0x1515,0x1616,0x1717,0x1818,0x1919,0x1a1a,0x1b1b,0x1c1c,0x1d1d,0x1e1e,0x1f1f,
    0x2020,0x2121,0x2222,0x2323,0x2424,0x2525,0x2626,0x2727,0x2828,0x2929,0x2a2a,0x2b2b,0x2c2c,0x2d2d,0x2e2e,0x2f2f,
    0x3030,0x3131,0x3232,0x3333,0x3434,0x3535,0x3636,0x3737,0x3838,0x3939,0x3a3a,0x3b3b,0x3c3c,0x3d3d,0x3e3e,0x3f3f,
    0x4040,0x4141,0x4242,0x4343,0x4444,0x4545,0x4646,0x4747,0x4848,0x4949,0x4a4a,0x4b4b,0x4c4c,0x4d4d,0x4e4e,0x4f4f,
    0x5050,0x5151,0x5252,0x5353,0x5454,0x5555,0x5656,0x5757,0x5858,0x5959,0x5a5a,0x5b5b,0x5c5c,0x5d5d,0x5e5e,0x5f5f,
    0x6060,0x6161,0x6262,0x6363,0x6464,0x6565,0x6666,0x6767,0x6868,0x6969,0x6a6a,0x6b6b,0x6c6c,0x6d6d,0x6e6e,0x6f6f,
    0x7070,0x7171,0x7272,0x7373,0x7474,0x7575,0x7676,0x7777,0x7878,0x7979,0x7a7a,0x7b7b,0x7c7c,0x7d7d,0x7e7e,0x7f7f,
    0x8080,0x8181,0x8282,0x8383,0x8484,0x8585,0x8686,0x8787,0x8888,0x8989,0x8a8a,0x8b8b,0x8c8c,0x8d8d,0x8e8e,0x8f8f,
    0x9090,0x9191,0x9292,0x9393,0x9494,0x9595,0x9696,0x9797,0x9898,0x9999,0x9a9a,0x9b9b,0x9c9c,0x9d9d,0x9e9e,0x9f9f,
    
  5. spi master与slave进入全双工模式,同时发送接收数据0x0000~0x009f,打印接收的数据:

    master receive data at quasi mode: 
    0x0000,0x0001,0x0002,0x0003,0x0004,0x0005,0x0006,0x0007,0x0008,0x0009,0x000a,0x000b,0x000c,0x000d,0x000e,0x000f,
    0x0010,0x0011,0x0012,0x0013,0x0014,0x0015,0x0016,0x0017,0x0018,0x0019,0x001a,0x001b,0x001c,0x001d,0x001e,0x001f,
    0x0020,0x0021,0x0022,0x0023,0x0024,0x0025,0x0026,0x0027,0x0028,0x0029,0x002a,0x002b,0x002c,0x002d,0x002e,0x002f,
    0x0030,0x0031,0x0032,0x0033,0x0034,0x0035,0x0036,0x0037,0x0038,0x0039,0x003a,0x003b,0x003c,0x003d,0x003e,0x003f,
    0x0040,0x0041,0x0042,0x0043,0x0044,0x0045,0x0046,0x0047,0x0048,0x0049,0x004a,0x004b,0x004c,0x004d,0x004e,0x004f,
    0x0050,0x0051,0x0052,0x0053,0x0054,0x0055,0x0056,0x0057,0x0058,0x0059,0x005a,0x005b,0x005c,0x005d,0x005e,0x005f,
    0x0060,0x0061,0x0062,0x0063,0x0064,0x0065,0x0066,0x0067,0x0068,0x0069,0x006a,0x006b,0x006c,0x006d,0x006e,0x006f,
    0x0070,0x0071,0x0072,0x0073,0x0074,0x0075,0x0076,0x0077,0x0078,0x0079,0x007a,0x007b,0x007c,0x007d,0x007e,0x007f,
    0x0080,0x0081,0x0082,0x0083,0x0084,0x0085,0x0086,0x0087,0x0088,0x0089,0x008a,0x008b,0x008c,0x008d,0x008e,0x008f,
    0x0090,0x0091,0x0092,0x0093,0x0094,0x0095,0x0096,0x0097,0x0098,0x0099,0x009a,0x009b,0x009c,0x009d,0x009e,0x009f,
    
    slave receive data at quasi mode: 
    0x0000,0x0001,0x0002,0x0003,0x0004,0x0005,0x0006,0x0007,0x0008,0x0009,0x000a,0x000b,0x000c,0x000d,0x000e,0x000f,
    0x0010,0x0011,0x0012,0x0013,0x0014,0x0015,0x0016,0x0017,0x0018,0x0019,0x001a,0x001b,0x001c,0x001d,0x001e,0x001f,
    0x0020,0x0021,0x0022,0x0023,0x0024,0x0025,0x0026,0x0027,0x0028,0x0029,0x002a,0x002b,0x002c,0x002d,0x002e,0x002f,
    0x0030,0x0031,0x0032,0x0033,0x0034,0x0035,0x0036,0x0037,0x0038,0x0039,0x003a,0x003b,0x003c,0x003d,0x003e,0x003f,
    0x0040,0x0041,0x0042,0x0043,0x0044,0x0045,0x0046,0x0047,0x0048,0x0049,0x004a,0x004b,0x004c,0x004d,0x004e,0x004f,
    0x0050,0x0051,0x0052,0x0053,0x0054,0x0055,0x0056,0x0057,0x0058,0x0059,0x005a,0x005b,0x005c,0x005d,0x005e,0x005f,
    0x0060,0x0061,0x0062,0x0063,0x0064,0x0065,0x0066,0x0067,0x0068,0x0069,0x006a,0x006b,0x006c,0x006d,0x006e,0x006f,
    0x0070,0x0071,0x0072,0x0073,0x0074,0x0075,0x0076,0x0077,0x0078,0x0079,0x007a,0x007b,0x007c,0x007d,0x007e,0x007f,
    0x0080,0x0081,0x0082,0x0083,0x0084,0x0085,0x0086,0x0087,0x0088,0x0089,0x008a,0x008b,0x008c,0x008d,0x008e,0x008f,
    0x0090,0x0091,0x0092,0x0093,0x0094,0x0095,0x0096,0x0097,0x0098,0x0099,0x009a,0x009b,0x009c,0x009d,0x009e,0x009f,
    

5 RAM/Flash资源使用情况

PAN107x:

FLASH Size:  14.05k
RAM Size:  7.81 k